E-Learning

Upon completion of this course, given a wired PowerFlex® 750-Series drive (PowerFlex 753 or PowerFlex 755) and AC motor, you will be able to properly install the drive, start up the drive, and configure drive parameters to meet application-specific needs.

Upon completion of this course, given a PowerFlex® 750-Series drive (PowerFlex® 753 or PowerFlex® 755) that has been successfully started up, you will be able to integrate your drive into a system that includes Logix 5000 controllers and PanelView Plus terminals running FactoryTalk View ME software.

After completing this course, you should be able to interpret ladder logic instructions for any Logix 5000™ controller.

Upon completion of this course, you should be able to demonstrate fundamental motion control concepts common to all Rockwell Automation motion control systems.

After completing this course, you should be able to configure, test, tune, and program CIP Motion™ axes using the Studio 5000 Logix Designer® application.

Upon completion of this course, given a functional specification for a Logix5000™ application, you should be able to develop a project to meet the specification requirements.

After completing this course, you should be able to perform basic ControlLogix® Logix 5000™ and Studio 5000 Logix Designer® tasks, such as creating and configuring a project and communicating with a controller.

After completing this course, you should be able to program basic ladder logic instructions for Logix5000™ controllers.

This course provides you with an understanding of Studio 5000 Logix Designer® function block diagrams and terminology.

After completing this course, you should be able to configure a Stratix® 5700 switch to meet a variety of network requirements; assign IP addresses to devices on an EtherNet/IP network; monitor switch performance and status and diagnose and resolve issues with switches and devices on the network.

After completing this course, you should be able to produce an operational application that runs on a PanelView Plus 7 terminal, given a computer with FactoryTalk View ME software and a PanelView Plus 7 terminal.

Upon completion of this course, you should be able to organize and develop FactoryTalk® View Site Edition (SE) applications.

Controls engineers have a strong domain knowledge of automation derived from fieldbus experience, while IT engineers have a strong domain knowledge of IP technologies from enterprise network deployments. This course provides both with a sufficient level of knowledge to allow them to collaboratively architect a machine or process skid network, or to operate as a credible domain expert in a multi-function team under the leadership of their counterpart.

Controls engineers have a strong domain knowledge of plant-wide integration of proprietary control systems, while IT engineers have a strong domain knowledge of integration of disparate data streams on a single network. This course provides both with a sufficient level of knowledge to allow them either to collaboratively architect a machine or process skid network ready for integration into a converged plant-wide network, or to operate as a credible domain expert in a multi-function team.

Controls engineers have a strong domain knowledge of plant-level system integration of highly complex process automation and PLC systems, while IT engineers have a strong domain knowledge of deploying highly disparate data services on a single network derived from voice, video and data convergence. This course provides both with a sufficient level of knowledge to allow them either to collaboratively architect a converged multi-service plant-wide network, or to operate as a credible domain expert in a multi-function team under the leadership of their counterpart.

Controls engineers have the domain knowledge of plant-level systems needed to identify transformational technologies and analysis that will dramatically improve production efficiency and flexibility. Meanwhile, IT engineers have the domain knowledge of presenting actionable information where it is needed within an enterprise and throughout the value chain. This course provides both with a sufficient level of knowledge to collaboratively architect a smart IAC's facility with internal and external stakeholders using cloud technologies.

After completing this course, you should be able to properly start up the drive and configure drive parameters to meet application-specific needs.

This course (CCP154-EL) provides the skills and knowledge to program using the structured text and sequential function chart programming languages in Studio 5000 Logix Designer®.

This course (SAF-LOG104-EL) provides you with the ability to create a Studio 5000 Logix Designer® project for a GuardLogix® system and troubleshoot a previously operational GuardLogix system.

This course (CCN144-A) will teach you to configure, test, tune, and program CIP Motion™ axes using the Studio 5000 Logix Designer® application.